Ozar Docs
  • Getting Started
    • 👩‍🚀Start Here
  • PumpFun Bundler & Trader
    • PumpFun Bundler - Your First Launch
    • Launch Strategies
    • Multi-Wallet Trader
    • Why am I asked to put in so much extra SOL
  • Wallet Utils
    • Withdraw Sol/Tokens
    • Distribute Sol
    • Reclaim Sol
    • Export, Reset & Import
  • PumpFun Extras
    • 📈Bump Bot
    • Market Cap Calculator
  • Referral and Fee
    • Fee
    • Referrals
Powered by GitBook
On this page
  • 1. Select Token
  • 2. Configure Bump Settings
  • 3. Review Cost Estimator
  • 4. Deposit Funds and Start
  • 5. Stopping and Withdrawing Funds
  • 6. Go to Past/Active Bumps
  1. PumpFun Extras

Bump Bot

Send your token to the top of the charts with our Bump Bot!

PreviousExport, Reset & ImportNextMarket Cap Calculator

Last updated 3 months ago

App:

Bump Bot is an essential tool to get your token on top of PumpFun Trending, BullX and Photon and boost the visibility of your token

1. Select Token

Just enter the CA of the token you wish to run the bump bot on and press/click 'GO'

2. Configure Bump Settings

Configure the following settings of the bump bot to run it efficiently and reliably.

  • Bump Amount - Configure the amount of each buy and sell. You have 3 options - (0.011, 0.015, 0.02) SOL. By default 0.011 SOL is selected and its recommended but sometimes Pumpfun might not register buys of 0.011 SOL, in this scenario consider raising the Bump Amount

  • Bumps Per Minute - Configure the speed of bumps. You can choose anywhere between 5 to 60 bumps per minute. We recommend running it at higher speeds (30+) as it increases your chances to be on top of the trending chart.

  • Priority Fee - Configure the Jito Tip (network fee) that you wanna pay for each bump. You can choose between Low, Medium and High. We recommend High for the maximum landing rate of your bumps i.e. reliability

3. Review Cost Estimator

The estimator will give a rough idea on how much SOL is required based on your desired duration of running bumps & the bump settings.

  1. Enter the time (in minutes) in the Desired Duration input box

  2. Review the estimated required balance - this is the amount that is required to run the bump bot for the desired duration on the selected bump settings. Remember you can put less or more SOL in the bot and the bot will run till it runs out of fuel (deposited SOL).

The minimum deposit amount is 0.02 SOL and the bot will automatically stop when the balance goes below it

4. Deposit Funds and Start

  1. Once you're satisfied with your bump settings, deposit SOL to the deposit address that is unique to your token. The minimum deposit amount is 0.02 SOL.

  2. When you have deposited the SOL, click on the refresh button to update the balance in the wallet

  1. After the balance is updated, click start bumping and the bump bot will start

It might take around 30-40 seconds for the bump bot to start

5. Stopping and Withdrawing Funds

Stopping - Click Stop Bumping and this will stop the bump bot. It will take a few seconds to stop the bump completely (4-5 seconds)

Withdraw - Withdraw your left over SOL to any wallet on the Solana blockchain by -

  1. Click on the Withdraw All button, it will show you the SOL balance left in the bot

  1. A pop up will show - Enter the public key of the wallet that you wanna withdraw the funds to and click withdraw. Shortly your funds will appear in your wallet.

Increase the Jito Tip in times of congestion to maximise your chances of landing your withdraw transaction

6. Go to Past/Active Bumps

To access your running/past bump orders click on the 'Go to Past/Active Bumps' button

This screen will show you your past and active bumps. From this screen you can -

  1. Stop any running bumps by clicking the order and then click Stop Bumping

  2. Open any selected bump order

  3. Withdraw your funds from any deposit address by clicking Withdraw All

App:

📈
app.ozar.pro
app.ozar.pro